Only touch a bucket if a find request targets it.

[quix0rs-apt-p2p.git] / apt-p2p.conf

diff --git a/apt-p2p.conf b/apt-p2p.conf
index 9a12eed990d0afe4803ba3afdd89040914fe7869..6d4a00fd985ad7e31c10c555aaf85954b08cbe3d 100644 (file)
--- a/apt-p2p.conf
+++ b/apt-p2p.conf
@@ -17,7 +17,17 @@
 # for uploads to other peers. If a port is not specified for the DHT, it will also
 # use this UDP port to listen for DHT requests.
 PORT = 9977
-    
+
+# The rate to limit sending data to peers to, in KBytes/sec.
+# Set this to 0 to not limit the upload bandwidth.
+UPLOAD_LIMIT = 0
+
+# The minimum number of peers before the mirror is not used.
+# If there are fewer peers than this for a file, the mirror will also be
+# used to speed up the download. Set to 0 to never use the mirror if
+# there are peers.
+MIN_DOWNLOAD_PEERS = 3
+
 # Directory to store the downloaded files in
 CACHE_DIR = /var/cache/apt-p2p
     
@@ -26,9 +36,12 @@ CACHE_DIR = /var/cache/apt-p2p
 #          for everybody to download
 # OTHER_DIRS = 
     
-# Whether it's OK to use an IP addres from a known local/private range
+# Whether it's OK to use an IP address from a known local/private range
 LOCAL_OK = no
 
+# Whether a remote peer can access the statistics page
+REMOTE_STATS = yes
+
 # Unload the packages cache after an interval of inactivity this long.
 # The packages cache uses a lot of memory, and only takes a few seconds
 # to reload when a new request arrives.
@@ -36,10 +49,13 @@ UNLOAD_PACKAGES_CACHE = 5m
 
 # Refresh the DHT keys after this much time has passed.
 # This should be a time slightly less than the DHT's KEY_EXPIRE value.
-KEY_REFRESH = 57m
+KEY_REFRESH = 2.5h
+
+# The user name to try and run as (leave blank to run as current user)
+USERNAME = apt-p2p
 
 # Which DHT implementation to use.
-# It must be possile to do "from <DHT>.DHT import DHT" to get a class that
+# It must be possible to do "from <DHT>.DHT import DHT" to get a class that
 # implements the IDHT interface. There should also be a similarly named
 # section below to specify the options for the DHT.
 DHT = apt_p2p_Khashmir
@@ -57,25 +73,20 @@ DHT-ONLY = no
 
 # bootstrap nodes to contact to join the DHT
 BOOTSTRAP = www.camrdale.org:9977
+            www.camrdale.org:9976
             steveholt.hopto.org:9976
 
 # whether this node is a bootstrap node
 BOOTSTRAP_NODE = no
 
-# Kademlia "K" constant, this should be an even number
-K = 8
-
-# SHA1 is 160 bits long
-HASH_LENGTH = 160
-
 # interval between saving the running state
 CHECKPOINT_INTERVAL = 5m
 
 # concurrent number of calls per find node/value request!
-CONCURRENT_REQS = 4
+CONCURRENT_REQS = 8
 
 # how many hosts to post values to
-STORE_REDUNDANCY = 3
+STORE_REDUNDANCY = 6
 
 # How many values to attempt to retrieve from the DHT.
 # Setting this to 0 will try and get all values (which could take a while if
@@ -94,8 +105,24 @@ MIN_PING_INTERVAL = 15m
 # refresh buckets that haven't been touched in this long
 BUCKET_STALENESS = 1h
 
+# Whether it's OK to add nodes to the routing table that use an IP
+# address from a known local/private range.
+# If not specified here, the LOCAL_OK value in the DEFAULT section will be used.
+# LOCAL_OK = no
+
 # expire unrefreshed entries older than this
-KEY_EXPIRE = 1h
+KEY_EXPIRE = 3h
+
+# Timeout KRPC requests to nodes after this time.
+KRPC_TIMEOUT = 9s
+
+# KRPC requests are resent using exponential backoff starting with this delay.
+# The request will first be resent after the delay set here.
+# The request will be resent again after twice the delay set here. etc.
+# e.g. if TIMEOUT is 9 sec., and INITIAL_DELAY is 2 sec., then requests will
+# be resent at times 0, 2 (2 sec. later), and 6 (4 sec. later), and then will
+# timeout at 9.
+KRPC_INITIAL_DELAY = 2s
 
 # whether to spew info about the requests/responses in the protocol
 SPEW = no